The only Aries Grille Guard that fits your 1999 Chevy S-10 is the part # AA4044 for which the replacement hardware kit is # AABRKT-4044. The only way that we can endorse that you mount your grille guard is with the hardware that is designed by Aries to fit because they have tested it that way. Anything else that you use hasn't been tested so there is the potential that it can damage your vehicle or not be as secured to your vehicle.
Please note that grille guards and their mounting hardware... view full answer...
I think you may be referring to the Bulkhead Seal for your BAKFlip Tonneau Cover, which we have available in the 3/8" thick # PARTS-326A0004 and the 1/4" thick # PARTS-326A0005. I'm not sure what exact model BAK cover you have so you will just want to measure your existing seal to determine the right replacement.
This is the strip that gets attached to the bed rails on your truck. view full answer...
Assuming your Extang Tuff Tonno is part # EX14525, the replacement tarp is # EX13525. The replacement is specific to that particular # EX14525, so if you have a different tonneau cover, please let me know. view full answer...
We do have hardware kits available for all the trailer hitches we carry. Checkout Replacement Hardware, part # RHK. You will then add the hitch number and manufacturer to the drop down box selections. The hitch number should be labeled on your hitch.
You will want to make sure to use the specified hardware from the hitch manufacturer.
I have linked all the hitches we have available for a 1998 Chevrolet S-10 pickup truck. Also linked is an FAQ on trailer hitch installation tips. view full answer...
If you have the Original Truxedo Edge or LoPro QT Tonneau cover on your 2002 S-10, The Velcro replacement you need is part # TX1115174. This is designed to fit the 6-1/2 ft bed and can be cut to work with the 4-1/2 ft bed as well. view full answer...
I spoke with Extang about the Extang Lo Pro Tonneau 8560 on your 1998 Chevrolet S-10 Pickup with 6' Bed and they informed me that you need the Replacement Cover for TruXedo Lo Pro Soft, Roll-up Tonneau Cover part # TX5560-CVR which is an exact fit, the same one that would have come with the cover when new. view full answer...
The Extang # EX1560 Replacement Tarp is the correct replacement part for a BlackMax tarp that fits a 2002 Chevy S10 with a 6-foot (non step side) bed.
If you additionally need replacement cab and tailgate end corners you can order Extang # EX4205-2. If you need replacement offset snap studs you can order Extang # EX2128. view full answer...
The best way to determine which line on a transmission cooler is the return line from the radiator is to use the following procedure:
1. Start engine while engine is cold
2. Place transmission shift lever in drive for no more than 10 seconds
3. Place in Park, stop engine, and remove keys
4. Identify the oil return line by feeling both oil lines. The coolest line is the oil return line.
On the aftermarket transmission cooler the ports are not input specific or output specific. It is not... view full answer...
Thank you for providing that information. What you have is a 6,000 lb Dexter axle. Based on the axle capacity and your leaf spring measurement you can use the 4-Leaf Double-Eye Spring # e47SR which measures 25-1/8" long. The slight difference in length isn't going to make a difference.
For an equalizer replacement you can use the Curved Equalizer for 1-3/4" Wide Double-Eye Springs # TREQE1. This measures 7-3/4" long x 2-7/8" tall.
For the rest of the components I highly recommend upgrading... view full answer...
For your 2001 Chevrolet S-10 Pickup and the TruXedo Lo Pro QT 539601 the replacement cover is part # TX539601-CVR.
I have confirmed this with my contact at TruXedo. view full answer...
We do have a replacement that will work for you, even though the lid alone is not available separately; however, the inlet of the Furrion RV Power Cord Conversion Kit 125V - 30 Amp is something you can get.
What you need is the Furrion 30 Amp Power Inlet - White - LED # 431861 which has the Powersmart LED indicator and is the same power inlet used in the kit so you do not have to purchase the entire kit, you can just get the inlet.
I have added a link to a video review of this inlet... view full answer...